Wall Hung Table

Wall Hung table

Making a table

The design process used cannot really be put into words. It blends a vision, an action plan, and selection of materials to get the job done. Whatever the project, the process is fluid and small details change as the project progresses because of a defect in available materials, after seeing the object a visual refinement is needed or sometimes you savage a mistaken cut. Rarely, a set of detail drawing exists. Most times a few measurements and a sketch or a picture is the extend of the design. Usually the project itself is the drawing board.

As an illustration, I will take your through a recent project to design and construct a wall hanging hall table. After making the piece, I decided to keep it and use the table as a desk instead of selling it to the original customer. This decision in part was because the customer changed her mind about the finish – opaque lacquer after the construction was completed – and I could not bring myself to covering the wood grain in the selected white oak material. Another reproduction was made using poplar and birch.

The design

The customer provided a picture from a magazine of blond colored table hung on a foyer hall. The table had a bow front. Using proportion from objects in the photograph – this a place where experience with architectural woodwork pays off – it was determined that the table was about 15 inches at the ends and about 22 inches at the apex of the bow front. The table had an apron around 6 inches deep with a single large drawer in the middle. The ends appeared as though they formed a gentle radius at the junction with the bow front. The table length was somewhere between 5 and 6 feet. The table was supported by two large ogee brackets. The brackets were the first deviation from the picture because they looked heavy and destroyed the illusion that the table was floating in space. A steam bend brackets (shown in later photographs) were substituted.

Given these measurements, it was decided to use white oak as the material and steam bend the apron and brackets. Quarter inch thick white oak can be bent to a 2 inch radius so this material would be perfect to form a continous surface for the apron. Laminating three pieces created a piece with enough rigidity to support the top and allow fastening to the carcase frame. From previous projects successes using thicker lumber , the bracket consisted of a lamination of two 3/4 inch thick bends. To provide the strength to support the piece as a cantilever off the wall, it was decided to use a torsion box construction method.

The first step to any steam bending project is construction of the bending form. The bending form is also the drawing board of the design process where you work out general dimension of piece.

You need to start with a bending form made from lamination for 3/4 plywood. The taper sides allowed for spring-back in the pieces

The only difference between the shape of the final piece and the bending form is the need to provide for “over bending” because the piece will “spring back” . Although this “tool” may look rough, its construction must be strong enough to withstand the clamping pressure necessary to force a piece of wood against its natural instincts and all surfaces must be machined so the surface is smooth and plumb. Any defect in the bending forms telegraphs into the piece being bent. Experience has taught that it takes about 3 to 4 hours to construct the form using plywood scraps, nails, screws and glue. The most important tool however is a router with a bottom bearing pattern bit used to clean up the bending surface between consecutive layers of plywood.

The next step was to select a six inch wide by 10 feet white oak board with straight and no knots. Any grain twist is likely to “blow out” during the bending process. This board was resawn with a bandsaw to yield two 5/16 inch pieces after milling away the saw marks. The pieces were placed in a steam chamber constructed from 10 inches round heating ducts that uses a electric turkey fryer as the steam generator. (shown without the fiberglass insulation wrapping)

The original plan was to bend and glue laminate these two pieces as one continous piece but reality destroyed the dream. The time it took to bend a piece around the form allowed the wood to cool too much before the second end could be forced to the form’s radius. The board cracked at the second corner radius on both pieces after forming a perfect surface at the first corner. The cracked face created a mental dilemma because the original concept was a continous formed surface – how do you get two good face looking out. I glued only the center section that will form the drawer front (31 inched in the center of the bow front). By cutting this section out after the glue dried, I was able to flip the ends so one good face looked out for the corners. I was not pleased with the appearance because the “good corner” had some cracked grain on one of the pieces. I decided to make a 4.5 feet section(1/4 inch thick) that included the side apron and the front apron to point where it met the drawer. These pieces were steam bend and then glue laminated to original project.

At this point, a small digression for any project that glue laminates. You can follow blogs and magazine articles that talk about this subject and arguments if the yellow glue that you can buy at Home Depot or Lowes is sufficent for this operation. My experience – or the myth that my minds tells me is correct – is that the yellow glue creeps too much for this stressed application and the short setting time can be problematic when during the summer months. I prefer the thermoplastic, rigid glue line obtained from the “plastic phenolic resin glues” that are powders mixed with water immediately before using. I have found success using PPR available from Woodworkers Supply or other internet catalog stores.

Using the bending template after modification to remove the “overbend” as a gluing form force the glue lamination to conform to the intended design. Ends are allowed to overhang and will be trimmed to the final measurement later with hand tools.

After adjusting the template an ash rail-stile-panel was made to conform to the pattern.

At this point the bottom surface of the torsion box is made from white ash (had enough secondary wood quality on hand) and 1/2 birch plywood panels. This surface used the rail and stile construction method. The apron is attached with pocket screws (no glue so any expansion and contraction frame would not transmit to the apron face).

Take out the twist in the steam bend by screwing it into the top mirror image frame.

The top torsion box member is formed in similar fashion but top member excludes the floating birch plywood panels. A top rail at the drawer opening is set back so it is not visible when the drawer is open. This top frame is attached to the internal web and apron with screws. All overhanging pieces are cut to the final dimension at this point using handsaws and razor cut scribe lines

The drawer front is made from two laminations glued and cut from the center of the original sides. To make the drawer construction stronger and make the machining easier, a secondary surface was created using a full length white oak board and two white oak scrap blocks. The drawer’s dovetails are machined in the blocks and then glue laminated to full length board. The outer surface is cut to the arc formed by the drawer front lamination using a bandsaw. After cleaning up and custom fitting, board is glued to the drawer front lamination. After the glue dries, the inner surface of the drawer is cut with a bandsaw to a modified mirror of the front surface. Later, the drawer botttom surface is covered with a red felt.

Cheater pieces allow a 90 degree alignment to fit into dovetail machine

The glue lamininated brackets that supports the table from the wall are trimmed so that it forms a 90 degrees angle with the rear (wall) surface. This step uses a framing square to scribe the angles, hand saw, and hand plane for the final finesse. The bracket attaches to the bottom torsion box member using screws (plugged counter-bore holes) and the wall support bracket with screws (blind) and glue. The wall support bracket attaches to the torsion box with glue and pocket screws.

Almost there and ready for finish and installation

You should note the 1/2 inch holes drilled in the torsion frame along the front and side edge. These holes allow access so the top can be screwed to the top torsion frame members.

After sanding, the surface was sealed using Penetrol. This product is a resin solvent blends sold to thin oil based paints before spraying or to lessen brush marks. If allowed to dry for at least three days, the material is an excellent primer for raw wood. If left untinted – as used in this project – it accents the natural grain and color of the wood. Adding artist colors, Penetrol makes an excellent base for custom stains or opaque finishes. The open pores were filled with a paste filler that were tinted to a light brown red using Indian red and Ochre yellow artist pigments. After drying and sanding with 220 grit sandpaper to remove the excess filler and level the surface, multiple coats of Sherwin Williams waterborne gloss polyurethane were wiped on. The finished surface was leveled with steel wool and scruff buffed with a abranet 500 pad attached to a random orbital sander. A crystal beewax added the final luster.

Install required a 2 3/8″ X 1.5″ X 58″ framing lumber member attached into the wall studs. The attachment beam fits between the upper and lower torsion box members. After sliding the table onto the support beam, four 3 inches long screws were drive from underside. Counter-bored holes through the bottom torsion member meant that the screws attached the support beam to the top torsion member. Another four screws were driven through the bottom torsion member into the support beam. The front edge was the table was leveled to the back edge using thin slims glued behind the wall support brackets.

Now you have seen a project from start to finish. What project do you have in mind. Contact me with comments, questions or ideas.

Veneer made from scrap lumber

Posted by Wilson Cunningham on 3:14 pm in Bedside, Boxes, Chest of drawers, Fairfax Virginia, Other, Tables, veneer | Comments Off on Veneer made from scrap lumber

Veneer Furniture Plywood contributes to a perception that veneer means a low quality, easily marred, low cost wooden objects. This perception contrasts historic use of thin wood slices that showcases the beauty of woods that are either rare, expensive, and/or possess natural artistic qualities. Adhering these slices to larger surfaces expand the size of the furniture that can use these unique natural resources. Additionally, by arranging grain orientation and color prior to the gluing, new visual appearances develop that are not available...

wall hung table

Posted by Wilson Cunningham on 1:44 pm in Architectural woodwork, Fairfax Virginia, Other, Steam bending, Tables | Comments Off on wall hung table

Wall hung table The client wanted a custom fitted reproduction of a foyer hall wall hung table she had seen in a magazine. The piece was scaled from the photograph and the length modified to fit its future home. The bow front wall hung table is constructed from white oak. The table’s apron consists of steam bent pieces attached to a torsion box frame to provide superior stability and strength. A solid white oak panel tops the apron. The original piece was supported on the wall with two heavy corbel brackets. A steam bent curved...

Mahogany table update

Posted by Wilson Cunningham on 1:20 pm in Dining Room, Fairfax Virginia, Tables | 1 comment

Solid Mahogany table In 1956 my parents bought “Craftique” a antique reproduction of a drop leaf table and china hutch. The pieces were certified as solid genuine mahogany by the Mahogany Association (Certificate Number SO 138859). The china hutch has remained functional by today’s standards but the table’s space saving drop leaf design meant the table had “too many legs (8 total)” to allow a large gathering from sitting comfortably. When the “she who must be obeyed” and I added new chairs to the dining room suite, we...

Three dimensional wood surface

Posted by Wilson Cunningham on 8:05 pm in Chest of drawers, Fairfax Virginia, Other, Stone and Wood | Comments Off on Three dimensional wood surface

Mission Style

Posted by Wilson Cunningham on 2:14 pm in Fairfax Virginia, Mission, side, Sofa, Tables | Comments Off on Mission Style

What I think of as mission style may be classified by others as Arts and Crafts. I view the style as “square” highlighted with arches and spindles substitues for solid panels. White Oak was wood of choice for the majority of furniture made of this style. The examples shown here used American Black Walnut instead. The plant stand/side table was originally designed because a client had an extra tile left over from a renovation of fireplace surround that I did. The tile inlay was the perfect protective surface for the plant...

Breakfast nook

Posted by Wilson Cunningham on 7:38 pm in Fairfax Virginia, Kitchen, Steam bending, Tables | Comments Off on Breakfast nook

Take a piece of wood and expose it to heat (steam) and the lignin that holds together the cellulose fibers will soften. When the wood is placed in compression it will bend (within the confines wood species fiber elasticity) to a new shape. When it cools and the lignin “hardens”, the piece will retain the new shape. This characteristic has been used in chairmaking (Windsor chairs bow backs are a perfect example), boat building, cane making, archery bows and other furniture. Bending allows furniture to escape the rectilinear...

Natural wood slabs

Posted by Wilson Cunningham on 4:23 pm in Fairfax Virginia, live edge wood slab, side, Sofa, Tables, wood slab | 1 comment

Natural wood slabs can sometimes be found if you have a relationship with small private sawmills. Natural wood slabs will have “raw edges” that once were the growing bark edge of the tree. As the word “Slab” suggests, pieces usually exceed 1 inch thick. Some pieces might be cutoffs where wood of no commercial value is removed before the “real money” sawing starts. It is not uncommon to find knots, branch burls, rot, mineral staining or defect resulting in holes in natural wood slabs. These defects may...

Inside-out barrel

Posted by Wilson Cunningham on 7:32 pm in Steam bending, Tables | Comments Off on Inside-out barrel

Have to admit I stole the concept for the design from a design spotlight in Fine Woodworking (Adrian Ferrazzutti page 83 April 2012). It was the most challenging project I have encountered in nearly 50 years of destroying forest resources. 16 ribs were steam bent from 3/8 inch cherry and white oak 2 inches wide slats. The fourteen inch radius was an easy bent. The cherry and oak pieces were bent together (cherry to the form, oak away from form) and the resulting “matched pair” formed a good glue bonding surface. I found that...

Reclaimed wood – Trash to Treasure

Posted by Wilson Cunningham on 2:30 pm in Other, reclaimed wood, side, Tables | Comments Off on Reclaimed wood – Trash to Treasure

Reclaimed wood can sometimes found sitting on the curb awaiting trash pickup. This piece of broken and abused furniture was never a fine piece of craftsmanship. I guess it was a tourist purchase while on a vacation in the Caribbean or Central American resort. Sanding off the top finish showed a grain pattern and color hidden by the original maker. Cutting out the interesting part and placing it on a new base made it something worth the effort to pick it up off the curb trash pile and give it a new life.

Sandstone and steam bending wooden table pieces

Posted by Ed on 4:49 pm in side, Steam bending, Stone and Wood, Tables | Comments Off on Sandstone and steam bending wooden table pieces

Six clear white oak boards are steam bend to a 14 inches radius. Three pieces 2.5 inches wide are glued to form a triangular apron to support the top. Triangular blocks are added at the intersection to help attachment of the three 1.5 inches legs. Small pegs are added to help epoxy the top in place. The sandstone is easily cut with a diamond blade and the edges eased with a diamond rasp.

« Older Entries

Next Entries »

Recent Posts

Categories